Radical Technologies
Call :+91 8055223360

MASTER CAM

Best MasterCam Training in Pune

Duration of Training : 40 hrs

MasterCam Syllabus 

INTRODUCTION TO SYSTEM

CP/TP Gview

This chapter  describes the geometry view, construction plane, and tool plane in Mastercam, and how to change them. The levels manager is also discussed.

Job Setup

This chapter  discusses the use of the Job Setup in Mastercam including using the materials library.

Operations Manager

 The operations manager is shown. Group operations, copying toolpaths are discussed. 

DRAWING EXERCISES

Exercise 1

chapter is a simple 2D drawing exercise using several line creation methods.

Exercise 2

This chapter exercise uses polar lines for construction geometry. The Xform Rotate function is used.

Exercise 3

This chapter is an intermediate 2D drawing exercise. Several methods of arc creation are used.

3D Wireframe

 This chapter is a simple 3D wireframe exercise covering the use of different construction planes.

Surfaces

 This chapter example covers modeling a hair dryer using several surface creation functions.

Solids

 This chapter is an example of a plastic cap modeled using the solid modeling functions in Mastercam. 

WCS DEMONSTRATIONS

WCS Demo

 This chapter is an introduction into using Mastercam’s work coordinate system (WCS) and the view manager.

Work Offset Demo

 This chapter demonstration shows the use of the WCS with work offsets. 

WIREFRAME TOOLPATHS

2D Contouring

 This chapter demonstration covers several aspects of 2D contouring toolpaths including Ramping and 2D Chamfer. 

3D Contouring

 This chapter covers 3D contouring and 3D chamfering. A custom stock file is used during toolpath verification.

Remachining

 This chapter is an example of using Mastercam’s remachining functions during 2D contouring and pocketing.

Pocketing

 Several pocketing styles are shown including pocket facing, island facing, and open pockets. 

SURFACE TOOLPATH ROUGHING

Rough Parallel

 This chapter demonstration shows using the surface rough parallel toolpath. Saving the verified file as an STL model is discussed.

Rough Plunge

 This chapter shows the surface rough plunge being used.

Rough Contour

 This chapter shows the rough contour toolpath style. Highspeed moves in the toolpath are shown.

Rough Pocket

 The rough pocket toolpath is shown.

Rough Radial

 This chapter  demonstrates the rough radial toolpath.

Rough Restmill

 This chapter shows the rough restmill toolpath along with its parameters.

Rough Flowline

 This chapter shows a toolpath using the rough flowline method.

Rough Project

 This chapter shows an nci file used for the rough project toolpath method. 

SURFACE TOOLPATH FINISHING

Finish Parallel

 This chapter shows the finish parallel toolpath.

Finish Pencil

 This chapter  shows the finish pencil toolpath style of machining.

Finish Parallel Steep

 This chapter describes the use of the finish parallel steep toolpath.

Finish Radial

 This chapter shows the use of the finish radial toolpath method.

Finish Project

 A 2D toolpath is used for projection onto the model using the finish project method.

Finish Flowline

 This chapter toolpath shows the finish flowline toolpath.

Finish Contour

 This chapter shows the use of the finish contour toolpath. Highspeed loops are shown.

Finish Shallow

 This chapter shows the finish shallow toolpath and verification.

Finish Scallop

 This chapter demonstrates the use of the finish constant scallop method and the toolpath being regenerated.

Finish Leftover

 This chapter describes the use of the finish leftover toolpath. 

MULTIAXIS TOOLPATH

Curve 5Ax Surf Control

 This chapter describes using the toolpath using the tool axis control set to surfaces.

Curve 5Ax Line Control

This chapter describes using the toolpath using the tool axis control set to lines.

Curve 5Ax Point Control

This chapter describes using the toolpath using the tool axis control set to a point.

Curve 5Ax Chain Control

 This chapter describes using the toolpath using the tool axis control set to a chain.

Flow 5Ax Surf Control

This chapter describes using the toolpath using the tool axis control set to surfaces.

Flow 5Ax Point Control

This chapter describes using the toolpath using the tool axis control set to a point.

Swarf 5Ax Lead In / Lead Out

 This chapter describes using the toolpath using entry and exit moves.

Swarf 5Ax Chain Rails Control

This chapter describes using the toolpath using chain rails control.

4th Axis Positioning

 4 Axis about “A” axis, along X axis (VMC)

Our Courses

Enquire Now











    This will close in 0 seconds

    Call Now ButtonCall Us
    Enquire Now










      X
      Enquire Now